Posted on: April 3, 2020 Posted by: admin Comments: 0


Thats the first parport card with that chipset I have heard of, most Moschip based cards are still using the , , and ones. Moschip notoriously does not. Drivers got on board – this is the content: Enclosed is what throws in a terminal: Do not install the driver enter the same address should work?

Uploader: Mejin
Date Added: 14 February 2004
File Size: 12.18 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 7483
Price: Free* [*Free Regsitration Required]

If it is a parallel port card, the drivers supplied will not work with EMC and you don’t need them. Retrieved from ” https: A bit more info required, to be able to assist you regards PS To speed things up, with the card installed run ‘lspci -vv ‘ from a terminal and post the resulting print relating to this card.

MCS9904 — PCIe to Quad Serial Controller

EPP isn’t needed for stepper systems as the input and output pins are in separate groups in the other modes. The individual pins are addressed simply by their numbers, as per the base parport eg.

The device has no drivers installed on your computer, or the drivers are configured incorrectly. Each extra parport needs to be attached to a thread ie.

Device driver code 10

Device driver code 10 Fast Device driver code 10 This page was last modified on 4 Lonuxat Navigation menu Personal tools Log in. Drivers got on board – this is the content: Hi You have said what the chipset is but not what the card is for.


When 99001 Confirm window pops up, check the Delete the driver software for this device checkbox and click OK. Sep 18, How to fix device cannot start code 10 Update the drivers for this device in Device Manager, click the Driver tab in the device’s Properties dialog box. Paraller is a single port card. The possible port addresses are 0x and 0x You need to experiment liunx each of the port addresses shown and see which gives you pins you can read.

Thats lnux first parport card with that chipset I have heard of, most Moschip based cards are still using the, and ones. Follow the instructions to update the driver. Nice to know it will work with EMC regards. Dual headed 2 port cards are very useful, especially where PCI slots are scarce.

We use cookies in order to give you liinux best possible experience on our website. Run lspci -vv from a terminal once installed and you will get a print similar to the below for your card.

CONFIG_PARPORT: Parallel port support (EXPERIMENTAL)

These are the most widely used chips by card manufacturers, irrespective of what the actual card is branded as. The kernel of this distribution is “linux 2. By continuing to use this site, you agree to our use of cookies. Powered by Kunena Forum.

If a USB device is generating the Code 10 error, uninstall every device under the Universal Serial Bus controllers hardware category in Device Manager as part of the driver reinstall. On this card, 0xc was the port on the card mischip 0xb the port connected via the flyer ribbon cable. Hi Glad you got it sorted.


Enclosed is what throws in a terminal: See link to Big JTs port tester as one option to test. Code 10 Other USB devices such as mice, keyboards, and Bluetooth adapters work fine That isManual driver update You can update the driver manually by going to the manufacturers website for the device that has the code 10 error, and searching for the most recent correct driver.

Code 10 If you are affected by this issue, do not fret as you have quite a few viable options when linhx comes to trying and solving the Code 10 issue.

MosChip MCS problem with the installation – LinuxCNC

Another simple option is to move a known good signal wire from a limit switch sayfrom the BOB connected mosxhip existing port, to new BOB and activate the switch whilst watching the relevant pins in Hal Configuration window.

This is a dual port card, some trial and linyx is required to establish which addresses are the ports and which the registers. From a quick scan of the net, they may not work with any Linux kernel higher than 2.


Leave a Comment